Welding inverter is an alternative to a conventional welding transformer. Modern semiconductors allow to replace the traditional mains transformer with a
switching power supply, which is much lighter, smaller and allows easy current adjustment via a potentiometer. The advantege is
also that the output current is DC. DC current is less dangerous than AC and prevents arc extinction.
For this inverter i chose topology, which is the most common in welding inverters - forward converter with two switches.
In my article about switchning supplies it is a topology II.D.
Input mains voltage passes through an EMI filter and is smoothed with high capacity capacitors. Since the inrush current of those capacitors would be too high,
there's a softstart circuit. After switching ON, the primary smoothing capacitors are charging via resistors, which are later bypassed
by the contact of a relay. As power switches, IGBT transistors IRG4PC40W are used.
They are driven through a forward gate-drive transformer TR2 and shaping circuits with BC327 PNP transistors.
The control integrated circuit is UC3844. It's similar to UC3842, but it has its pulse-width limited to 50%. Working frequency is 42kHz.
Control circuit is powered by an auxiliary power supply of 17V.
Current feedback, due to high currents, is using a current transformer Tr3. Voltage drop accros the sensing resistor 4R7/2W is approximately proportional to the output current.
Output current can be controlled by potentiometer P1, which determines the threshold of the current feedback. Threshold voltage of the pin 3 of UC3844 (current sensing) is 1V.
Power semiconductors require cooling. Most of the heat is dissipated in output diodes. Upper diode, consisting of 2x DSEI60-06A, must in worst
case handle the average current of 50A and the dissipation of 80W (total of both diodes).
Lower diode STTH200L06TV1 (doube diode package with both internal diodes connected in parallel) must in worst
case handle an average current of 100A and the dissipation of nearly 120W. Maximum total dissipation of the secondary rectifier is 140W. The heatsink must be able to handle it.
To the thermal resistance you must include the junction-case Rth, case-sink Rth and sink-ambient Rth.
DSEI60-06A diodes don't have insulation pads and the cathode is connected to the the heatsink. Output choke L1 is therefore in the negative rail. It
is advantageous because in this configuration, there's no high-frequency voltage on the heatsink.
You can use another type of diodes, for example a parallel combination of a sufficient number of the most accessible diodes,
such as MUR1560 or FES16JT. Note that the maximum average current of the lower diode is twice the current of the upper diode.
Calculation of the power dissipation of the
IGBTs is more complicated because in addition to conductive losses there are also switching losses. Loss of each transistor is up to about 50W.
It is also necessary to cool the reset diodes UG5JT and the mains bridge rectifier. The power dissipation of the reset diodes depends on the construction of Tr1
(inductance, stray inductance), but is much lower than the dissipation of the IGBTs. The rectifier bridge has a power dissipation of up to about 30W.
UG5JT diodes and the rectifying bridge are placed on the same heatsink as the IGBTs. UG5JT diodes
also can be replaced with MUR1560 or FES16JT or other ultrafast diodes.
During construction it is also necessary to decide the maximum loading factor of the welding inverter, and accordingly select size of heatsinks, winding gauges and so on.
It is also good to add a fan.
Switching transformer Tr1 is wound on two ferrite EE cores, each with a central column cross section 16x20mm. The total cross section is therefore
16x40mm, the core must have no air gap. 20 turns primary winding is wound using 14 wires of a 0.5 mm diamater. It would be better to use 20 wires, but they
didn't fit into my core.
Secondary winding has 6 turns of a copper strip (36 x 0.5 mm). Forward gate-drive transformer Tr2 is made with an emphasis on low stray inductance. It is trifillary wound,
using three twisted insulated wires of 0.3 mm diameter, and all the windings have 14 turns. Core is made of material H22, middle column has a diameter of 16mm, with no gaps.
Current sensing transformer Tr3 is made from an EMI suppression choke on a toroidal core. The original winding with 75 turns of 0.4 mm wire works as a secondary.
Primary has just 1 turn. Polarity of all the transformer windings must be kept (see dots in schematic)!
L1 inductor has a ferrite EE core, middle column has cross section 16x20mm. It has 11 turns of a copper strip (36 x 0.5mm) and the total air gap in the magnetic circuit is 10mm.
Its inductance is cca 12uH.
The auxiliary 17V switching power supply, including Tr4, is described in more detail
here.
The simplest welding inverter on Pic 1 has no voltage feedback. Voltage feedback does not affect the welding, but affects the power consumption and heat losses in the idle state.
Without the output voltage feedback there is quite high output voltage (approximately 100V)
and the PWM controller ia running at its max duty cycle, thereby increasing the power consumption and heating of components.
Therefore, it is better to implement the voltage feedback. You can inspire on Pic 2. The feedback can be connected directly because the controll circuit is
isolated from mains. The reference voltage is 2.5V. Select the R2 to set the open circuit voltage.
You can find useful info in datasheet of UC3842, 3843, 3844, 3845 or in its another datasheet.
Inspiration for modifications you can also find in 3-60V 40A supply.
Interesting links from which I drew:
http://svarbazar.cz/phprs/index.php?akce=souvis&tagid=3
http://leo.wsinf.edu.pl/~leszek/spawarki/
http://www.y-u-r.narod.ru/Svark/svark.htm
http://www.emil.matei.ro/weldinv3.php
http://nexor.electrik.org/svarka/barmaley/kosoy/shema.gif
and a little modified: http://nexor.electrik.org/svarka/barmaley/kosoy1/shema.gif
The is not an official release. Instead, it is a reverse-engineered patch that bypasses the authentication servers. Instead of connecting to a global server, the game redirects all calls to a local host (127.0.0.1) or a purely offline instance. The result? A single-player, sandbox version where you are the admin.
Never reuse your official account credentials (usernames or passwords) when setting up a local offline profile or registering on community modding forums. Final Verdict
While the idea of an unlocked, free offline version of 3DXChat is highly appealing, downloading and installing unofficial game modifications carries substantial risks that every user must consider. 1. Malware and Security Threats
Do you need help troubleshooting a specific or loopback issue? Share public link 3DXChat Ver2.6 Build 390 Offline Mod
Most offline packages include a local server emulator executable (often named Server.exe or LocalHost.bat ). Run the local server executable as an .
In the offline environment, you act as the local administrator. You can immediately unlock: All high-end clothing, footwear, and accessories. The entire library of custom animations and poses.
Do you already have the , or are you starting from scratch? Are you planning to add custom content/mods to it? The is not an official release
To understand why Build 390 is highly sought after by modders, it helps to look at where it sits in the game's development timeline. Version 2.6 represents a highly stable, feature-rich era of the game before major structural overhauls changed how data was handled by the official servers. Why Build 390?
The modding community for 3DXChat is incredibly active, creating custom clothing, textures, and poses. When the game engine changed, the method for importing these custom assets also changed. The tools developed by the community (often utilizing tools like uTinyRipper or AssetStudio) worked exceptionally well with the file structure of Build 390. Later updates by the developers encrypted game assets to prevent ripping and modding, making Build 390 the last "open" version that was easy for modders to manipulate.
You will likely need to create a "local" account within the mod's interface since it cannot retrieve your official online character. Key Considerations The result
Why would you want to play an older build when newer versions exist? Here are the standout features that make this specific version a fan favorite:
Many downloads are bundled with malicious software, such as .
Run the modified executable as an Administrator. When prompted at the login screen, entering any dummy username and password will grant access to the main dashboard. Limitations of the Offline Mod
For those who have been around the block in the world of adult MMOs, you know that the landscape changes rapidly. Official servers get updated, game engines get overhauled, and sometimes, the features we loved the most get left behind in the pursuit of monetization or technical restructuring. While the official version of 3DXChat has moved on to newer builds with Unity engine upgrades and different networking architectures, there is a dedicated subset of the community that still cherishes the 2.6 era.
Many modern simulation games and platforms are designed with "always-online" architectures, requiring constant communication with a central server for authentication, data storage, and social features. However, there is often significant user interest in offline functionality for several technical and practical reasons:
